Q&A


Flushing Issue

Excessive water splashes during flushing

The flushing may not operate properly under the following condition:

1. If the water pressure in the bathroom is high:
Please adjust the water pressure using the valve connected to the bidet's water supply hose.
(Turn clockwise to adjust the water pressure.)


Flushing does not work

The flushing may not operate properly under the following conditions:

1. If the toilet bowl is clogged:
Press the jet button on the manual flush button to check if the toilet bowl is clogged.
(If clogged, there will be no water flow, only bubbles.)

2. If the water pressure in the bathroom is low:
2-1. Adjust the water pressure using the valve connected to the bidet's water supply hose.
(Turn counterclockwise to fully open the valve.)
2-2. Remove the pressure reduction valve for flushing.
(Pressure reduction valve removal guide)

3. If water is being used elsewhere simultaneously:
Our bidet operates directly from the customer's water pressure. When water is being used elsewhere (washing machine, sink, shower), it may result in reduced water pressure, affecting drainage.

4. If the original water pressure is low:
Check the water pressure at your home.
(If the pressure is less than 1.5kgf/㎠, drainage may not be efficient.)
(To confirm the minimum required water pressure: Open the water supply valve fully and collect water in a container for 10 seconds, then check the quantity (3.5 liters).)

5. If a dual valve is installed:
Remove the dual valve and use our bidet's water supply hose.


Remote not working

Remote not working

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If power is not supplied to the bidet:
Check if the POWER LED on the main display panel is lit.

3. If the remote control ran out of battery:
Press the buttons on the remote control to see if the LED light on the remote control lights up. If the LED light is off, replace the batteries with new ones.

4. If there is an issue with the remote control buttons:
Turn on the camera function of your mobile phone and aim it at the remote control receiver.
While looking at your phone's screen, repeatedly press the malfunctioning buttons on the remote control.
(If only certain buttons do not emit light, there may be an issue with the remote control.)


Remote not powered

Problems may arise under the following circumstances:

1. If the remote control ran out of battery:
Press the buttons on the remote control to see if the LED light on the remote control lights up. If the LED light is off, replace the batteries with new ones.

2. If there is an issue with the remote control buttons:
Turn on the camera function of your mobile phone and aim it at the remote control receiver.
While looking at your phone's screen, repeatedly press the malfunctioning buttons on the remote control.
(If only certain buttons do not emit light, there may be an issue with the remote control.)


Remote not working even though there is a beep sound

Problems may arise under the following circumstances:

1. If the seat sensor does not detect human skin:
How to check if the seat sensor is operational
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
After the nozzle comes out, please ensure that the nozzle goes in when you make skin contact with the seat sensor (located on the left thigh area).

* Our bidet requires seat sensor (located on the left thigh area) to detect human skin in order for all nozzle function to operate.


All other functions operate except stop function
>Only specific function is not working

Problems may arise under the following circumstances:

1. If there is an issue with the remote control buttons:
Turn on the camera function of your mobile phone and aim it at the remote control receiver.
While looking at your phone's screen, repeatedly press the malfunctioning buttons on the remote control.
(If only certain buttons do not emit light, there may be an issue with the remote control.)


Function malfunctioning

Bidet does not power on

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If power is not supplied to the bidet:
Check if the POWER LED on the main display panel is lit.


Seat temperature does not change even after setting the temperature.
> seat is not warm.

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the bidet seat temperature setting is at level 0:
Adjust the bidet seat temperature to levels 1 to 3 using the remote control before use.
(Please confirm the reception sound (beep) from the bidet when adjusting the seat temperature.)
(It takes approximately 5 minutes to warm up the seat. Please wait for about 5 minutes after setting the seat temperature before use.)

3. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


The seat feels lukewarm.
>The seat is not warm.

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the bidet seat temperature setting is at level 0:
Adjust the bidet seat temperature to levels 1 to 3 using the remote control before use.
(Please confirm the reception sound (beep) from the bidet when adjusting the seat temperature.)
(It takes approximately 5 minutes to warm up the seat. Please wait for about 5 minutes after setting the seat temperature before use.)

3. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


Sometimes the seat feels cold.
>The seat is not staying warm.

Problems may arise under the following circumstances:

1. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


The seat is always warm even without setting temperature.

Problems may arise under the following circumstances:

1. If the seat temperature setting is at level 3:
Adjust the seat temperature to levels 0 to 1 using the remote control before use.
(Please confirm the beep sound from the bidet when adjusting the seat temperature.)


Sometimes the circuit breaker trips.

Problems may arise under the following circumstances:

1. If the power cord is not properly connected:
Ensure that the power plug is securely inserted into the outlet, as loose connections can cause issues.
(Be sure to use an AC 120V~, 60Hz outlet with proper grounding.)

* TCB-090SA/RTB-090WA/PB-707S/PB-101S : 703W
* TCB-8100W/TCB-8100B : 1180W

2. If there are electrical issues with the bathroom outlet:
Disconnect the bidet power plug from the outlet and plug in another electronic device such as a hairdryer to see if the circuit breaker trips.
→ If the circuit breaker trips, contact the building management or an electrician to inspect the electrical outlet.


The drying function is not warm.
>The drying is not warm

Problems may arise under the following circumstances:

1. If there is no power in the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the drying temperature setting is at level 0:
Adjust the drying temperature to levels 1 to 3 using the remote control before use.
* If the drying temperature is set at level 0 or 1, you may experience weak drying air.
* If the air speed is too strong, it may cause odor to rise, so we have not set the air speed to strong in order to prevent odor from rising.


Flushing sometimes does not work

Problems may arise under the following circumstances:

1. If the automatic flushing setting is OFF;
Please turn on the automatic flushing function using the remote control.

2. If the seat sensor does not detect human skin:
How to check if the seat sensor is operational
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
After the nozzle comes out, please ensure that the nozzle goes in when you make skin contact with the seat sensor (located on the left thigh area).

* Our bidet requires seat sensor (located on the left thigh area) to detect human skin in order for all nozzle function to operate.


Flushing does not work

Problems may arise under the following circumstances:

1. If the automatic flushing setting is OFF;
Please turn on the automatic flushing function using the remote control.

2. If the seat sensor does not detect human skin:
How to check if the seat sensor is operational
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
After the nozzle comes out, please ensure that the nozzle goes in when you make skin contact with the seat sensor (located on the left thigh area).

* Our bidet requires seat sensor (located on the left thigh area) to detect human skin in order for all nozzle function to operate.


External appearance defect

Crack on the exterior

Problems may arise under the following circumstances:

1. If you clean the exterior using cleaning agents such as Thinner, Benzene, Lysol, or toilet detergents, discoloration or damage may occur.

2. Scratches may occur during cleaning.
To avoid damage or scratches, please use a soft cloth for cleaning.


Scratch on the exterior

Problems may arise under the following circumstances:

1. If you clean the exterior using cleaning agents such as Thinner, Benzene, Lysol, or toilet detergents, discoloration or damage may occur.

2. Scratches may occur during cleaning.
To avoid damage or scratches, please use a soft cloth for cleaning.


Seat not staying upright
>Fixture exists behind the seat cover

Problems may arise under the following circumstances:

1. If there is a narrow gap between the seat cover and any fixtures behind the seat cover preventing the seat cover to fully open,
Please use the offset flange, pull it forward, and reinstall the toilet bowl.
(If the gap between the bidet and any fixtures behind the seat cover is narrow, the bidet's seat cover and seat may not stay up in place.)


The edge strip of the seat cover is peeling off.

Problems may arise under the following circumstances:

1. In cases of high or low external temperatures,
The bidet seat cover's adhesive strip may occasionally come loose. This is due to external temperature fluctuations and not a product defect. Simply press the strip back into place manually to reattach it.


Toilet bowl rust formation

Problems may arise under the following circumstances:

1. If not in use for an extended period,
After flushing, use soap and an abrasive cleaner to remove any residue.
Extended periods of non-use may cause iron deposits to settle and rust to form.


When sitting on the seat and urinating, urine splashes.

Problems may arise under the following circumstances:

1. When sitting on the seat and using it from the outside;
Please sit as far back inside the bidet as possible before use.



Nozzle Not operating

The nozzle water pressure is weak.

Problems may arise under the following circumstances:

1. If the water supply valve is not fully open (if the water pressure at your home is less than 1 kgf/㎠):
Please fully open the valve connected to the bidet hose.
- Check the water pressure at your home. (If the water pressure is less than 1 kgf/㎠, the water sprayed from the nozzle may be reduced.)

2. If the nozzle water pressure setting is at level 1:
Adjust the water pressure using the remote control before use.

3. If there is debris in the mesh:
Detach the water supply hose, clean the mesh, and then use it. (Refer to the mesh cleaning guide)

4. If the bidet water supply hose is bent or the water supply hose assembly is incorrect:
Check if the water supply hose is tangled or bent before use.
Detach the water supply hose and check the rubber packing on the hose before use. (Bidet hose check guide)


The nozzle comes out, but no water comes out.

Problems may arise under the following circumstances:

1. If the water supply valve is not fully open (if the water pressure at your home is less than 1 kgf/㎠):
Please fully open the valve connected to the bidet hose.
- Check the water pressure at your home. (If the water pressure is less than 1 kgf/㎠, the water sprayed from the nozzle may be reduced.)

2. If the nozzle water pressure setting is at level 1:
Adjust the water pressure using the remote control before use.

3. If there is debris in the mesh:
Detach the water supply hose, clean the mesh, and then use it. (Refer to the mesh cleaning guide)

4. If the bidet water supply hose is bent or the water supply hose assembly is incorrect:
Check if the water supply hose is tangled or bent before use.
Detach the water supply hose and check the rubber packing on the hose before use. (Bidet hose check guide)


The nozzle does not come out / does not retract.

Problems may arise under the following circumstances:

1. If water is not supplied to the bidet:
Fully open the valve connected to the bidet hose, then unplug the bidet power cord for 1 minute before plugging it back in to supply water to the bidet.

2. If there is a reception failure in the remote control:
Press the LED button on the remote control to verify if the bidet is operational.

3. If the seat sensor does not detect human skin:
How to check if the seat sensor is operational
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
After the nozzle comes out, please ensure that the nozzle goes in when you make skin contact with the seat sensor (located on the left thigh area).

* Our bidet requires seat sensor (located on the left thigh area) to detect human skin in order for all nozzle function to operate.


The nozzle does not dispense warm water.
>The water is not warm.

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the warm water temperature setting is at level 0:
Adjust the warm water temperature to levels 1 to 3 using the remote control before use.
(It takes approximately 3 to 4 minutes to heat the water. Please wait for 3 to 4 minutes after setting the warm water temperature before use.)

3. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


Flushing function works but the nozzle function does not.

Problems may arise under the following circumstances:

1. If the seat sensor does not detect human skin:
How to check if the seat sensor is operational
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
After the nozzle comes out, please ensure that the nozzle goes in when you make skin contact with the seat sensor (located on the left thigh area).

* Our bidet requires seat sensor (located on the left thigh area) to detect human skin in order for all nozzle function to operate.



Leakage

Leakage near the high-pressure hose.

Problems may arise under the following circumstances:

1. If the water supply hose connection is not properly done:
Close the valve connected to the bidet's water supply hose, then disassemble and reassemble the bidet and water supply hose to ensure proper connection. Check for any leakage afterwards.


Water drips slowly from the right side of the bidet nozzle.

Problems may arise under the following circumstances:

1. If the water pressure at your home is above 6kgf/㎠
If the water pressure at your home is above 6kgf/cm2, it may cause minor leakage. Please lower the water pressure to below 6kgf/cm2 before use.


There is leakage from the bottom of the bidet unit.

Problems may arise under the following circumstances:

1. If the water supply hose is not properly connected:
Close the valve connected to the bidet's water supply hose and reassemble the bidet and the water supply hose. Then check for any leaks.

2. If the connection between the upper bidet unit and the ceramic bowl unit is not properly established:
Reassemble the upper bidet unit and the ceramic bowl unit, then check for any leaks.



Auto Open /Close

Auto open and close function not working

Problems may arise under the following circumstances:

1. If the automatic open/close setting is OFF;
Please set it to ON using the remote control and then check the function. (When the automatic open/close setting is ON, only the seat cover will open/close when a person or object is detected in front of the bidet. If there is no one present, it will automatically close after about 90 seconds.)


When the AUTO open/close function is activated, there is a buzzing noise.

Problems may arise under the following circumstances:

1. If you forcibly open or close the seat or seat cover
Please open both the seat and seat cover, unplug the bidet power cord for 1 minute, and then plug it back in to reset the bidet. (Forcibly opening or closing without using the remote control buttons may cause the automatic open/close function to malfunction.)


When pressing the seat open/close button, it doesn't fully open, and closes instead.

Problems may arise under the following circumstances:

1. If you forcibly open or close the seat or seat cover
Please open both the seat and seat cover, unplug the bidet power cord for 1 minute, and then plug it back in to reset the bidet. (Forcibly opening or closing without using the remote control buttons may cause the automatic open/close function to malfunction.)


The seat cover sometimes opens and closes on its own

Problems may arise under the following circumstances:

1. If there are moving objects around the bidet;
Please remove them from the vicinity of the bidet.
(If moving objects are detected after the automatic opening/closing setting, the seat cover will open and close after 90 seconds.)



Noise

There is noise when sitting on the seat.

Problems may arise under the following circumstances:

1.If the deodorization function is turned on:
For models equipped with a deodorization feature, the sound you hear when seated is the deodorization fan operating.
Deodorization activates when seated and operates for 1 minute after the seat sensor no longers detects human skin.


After flushing, there is a dripping sound of water

Problems may arise under the following circumstances:

1.If there is noise coming from the front of the bidet:
It is the sound of residual water being discharged, typically occurring for around 30 seconds after flushing.

2. If there is noise coming from the back of the bidet:
It is the sound of residual water flowing over after flushing.



ETC

There is no water leakage, but there is an odor

Problems may arise under the following circumstances:

1. If the plumbing and toilet bowl are not connected properly:
Check the connection between the flange, wax ring, and the toilet bowl's drainage hole.
(Installation may not have been done correctly.)


When flushing, foam is generated, and water spurts out.

Problems may arise under the following circumstances:

1. If there is foreign matter inside the toilet;
Please refrain from disposing of foreign objects such as wet wipes or sanitary pads inside the bidet. Dispose of them in a trash bin instead. Foreign objects can cause clogging and water drainage issues.


There is an electric shock when sitting on the seat.

Problems may arise under the following circumstances:

1.If the electrical outlet in the bathroom is not grounded:
Please check if the electrical outlet connected to the product is properly grounded.
For safety purposes, it is necessary to use an electrical outlet with a grounding terminal.


Missing Parts

1. Please confirm the model name and purchase through our customer support center.
How to confirm the model name: Check the model name written on the back of the bidet unit.



Remote not working

Remote not working

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If power is not supplied to the bidet:
Check if the POWER LED on the main display panel is lit.

3. If the remote control's batteries ran out of battery:
Press the buttons on the remote control to see if the LED light on the remote control lights up. If the LED light is off, replace the batteries with new ones.

4. If there is an issue with the remote control buttons:
Turn on the camera function of your mobile phone and aim it at the remote control receiver.
While looking at your phone's screen, repeatedly press the malfunctioning buttons on the remote control.
(If only certain buttons do not emit light, there may be an issue with the remote control.)


Remote not powered

Problems may arise under the following circumstances:

1. If the remote control's batteries ran out of battery:
Press the buttons on the remote control to see if the LED light on the remote control lights up. If the LED light is off, replace the batteries with new ones.

2. If there is an issue with the remote control buttons:
Turn on the camera function of your mobile phone and aim it at the remote control receiver.
While looking at your phone's screen, repeatedly press the malfunctioning buttons on the remote control.
(If only certain buttons do not emit light, there may be an issue with the remote control.)


Remote not working even though there is a beep sound

Problems may arise under the following circumstances:

1. If the seat sensor does not detect human skin:
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
(Our bidet requires seat sensor(located under your left thigh area) to detect human skin in order for all nozzle function to operate.)


All other functions operate except stop function
>Only specific function is not working

Problems may arise under the following circumstances:

1. If there is an issue with the remote control buttons:
Turn on the camera function of your mobile phone and aim it at the remote control receiver.
While looking at your phone's screen, repeatedly press the malfunctioning buttons on the remote control.
(If only certain buttons do not emit light, there may be an issue with the remote control.)


Function malfunctioning

Bidet does not power on

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If power is not supplied to the bidet:
Check if the POWER LED on the main display panel is lit.


Seat temperature does not change even after setting up the temperature.
> seat is not warm.

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the bidet seat temperature setting is at level 0:
Adjust the bidet seat temperature to levels 1 to 3 using the remote control or side control panel before use.
(Please confirm the reception sound (beep) from the bidet when adjusting the seat temperature.)
(It takes approximately 5 minutes to warm up the seat. Please wait for about 5 minutes after setting the seat temperature before use.)

3. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


The seat feels lukewarm.
>The seat is not warm.

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the bidet seat temperature setting is at level 0:
Adjust the bidet seat temperature to levels 1 to 3 using the remote control or side control panel before use.
(Please confirm the reception sound (beep) from the bidet when adjusting the seat temperature.)
(It takes approximately 5 minutes to warm up the seat. Please wait for about 5 minutes after setting the seat temperature before use.)

3. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


Sometimes the seat feels cold.
>The seat is not staying warm.

Problems may arise under the following circumstances:

1. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


The seat is always warm even without temperature setting.

Problems may arise under the following circumstances:

1. If the seat temperature setting is at level 3:
Adjust the seat temperature to levels 0 to 1 using the remote control or side control panel before use.
(Please confirm the beep sound from the bidet when adjusting the seat temperature.)


Sometimes the circuit breaker trips.

Problems may arise under the following circumstances:

1. If the power cord is not properly connected:
Ensure that the power plug is securely inserted into the outlet, as loose connections can cause issues.
(Be sure to use an AC 120~, 60Hz outlet with proper grounding.)
* VB-6000 / VB-4000 / VB-3000 : 1200W

2. If there are electrical issues with the bathroom outlet:
Disconnect the bidet power plug from the outlet and plug in another electronic device such as a hairdryer to see if the circuit breaker trips.
→ If the circuit breaker trips, contact the building management or an electrician to inspect the electrical outlet.


The drying function is not warm.
>The drying is not warm.

Problems may arise under the following circumstances:

1. If there is no power in the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the drying temperature setting is at level 0:
Adjust the drying temperature to levels 1 to 3 using the remote control or side control panel before use.
* If the drying temperature is set at level 0 or 1, you may experience weak drying air.
* If the air speed is too strong, it may cause odor to rise, so we have not set the air speed to strong in order to prevent odor from rising.


Nozzle Not operating

The nozzle water pressure is weak.

Problems may arise under the following circumstances:

1. If the water supply valve is not fully open (if the water pressure at your home is less than 1 kgf/㎠):
Please fully open the valve connected to the bidet hose.
- Check the water pressure at your home. (If the water pressure is less than 1 kgf/㎠, the water sprayed from the nozzle may be reduced.)

2. If the nozzle water pressure setting is at level 1:
Adjust the water pressure using the remote control or side control panel before use.

3. If there is debris in the mesh:
Detach the water supply hose, clean the mesh, and then use it. (Refer to the mesh cleaning guide)

4. If the bidet water supply hose is bent or the water supply hose assembly is incorrect:
Check if the water supply hose is tangled or bent before use.
Detach the water supply hose and check the rubber packing on the hose before use. (Bidet hose check guide)


The nozzle comes out, but no water comes out.

Problems may arise under the following circumstances:

1. If the water supply valve is not fully open (if the water pressure at your home is less than 1 kgf/㎠):
Please fully open the valve connected to the bidet hose.
- Check the water pressure at your home. (If the water pressure is less than 1 kgf/㎠, the water sprayed from the nozzle may be reduced.)

2. If the nozzle water pressure setting is at level 1:
Adjust the water pressure using the remote control or side control panel before use.

3. If there is debris in the mesh:
Detach the water supply hose, clean the mesh, and then use it. (Refer to the mesh cleaning guide)

4. If the bidet water supply hose is bent or the water supply hose assembly is incorrect:
Check if the water supply hose is tangled or bent before use.
Detach the water supply hose and check the rubber packing on the hose before use. (Bidet hose check guide)


The nozzle does not come out / does not retract.

Problems may arise under the following circumstances:

1. If water is not supplied to the bidet:
Fully open the valve connected to the bidet hose, then unplug the bidet power cord for 1 minute before plugging it back in to supply water to the bidet.

2. If there is a reception failure in the remote control or side control panel:
Press the LED button on the remote control or side control panel to verify if the bidet is operational.

3. If the seat sensor does not detect human skin:
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
Our bidet requires seat sensor(located under your left thigh area) to detect human skin in order for all nozzle function to operate.


The nozzle does not dispense warm water.
>The water is not warm.

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the warm water temperature setting is at level 0:
Adjust the warm water temperature to levels 1 to 3 using the remote control or side control panel before use.
(It takes approximately 3 to 4 minutes to heat the water. Please wait for 3 to 4 minutes after setting the warm water temperature before use.)

3. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


Leakage

Leakage near the high-pressure hose.

Problems may arise under the following circumstances:

1. If the water supply hose connection is not properly done:
Close the valve connected to the bidet's water supply hose, then disassemble and reassemble the bidet and water supply hose to ensure proper connection. Check for any leakage afterwards.


Water drips slowly from the right side of the bidet nozzle.

Problems may arise under the following circumstances:

1. If the water pressure at your home is above 6kgf/㎠
If the water pressure at your home is above 6kgf/cm2, it may cause minor leakage. Please lower the water pressure to below 6kgf/cm2 before use.


There is leakage from the bottom of the bidet unit.

Problems may arise under the following circumstances:

1. Check the bottom of the bidet after removing it to inspect the water drainage bolt is open.
(Refer to the bidet removal guide and the guide on how to secure the water drainage bolt.)


External appearance defect

Crack on the exterior

Problems may arise under the following circumstances:

1. If you clean the exterior using cleaning agents such as Thinner, Benzene, Lysol, or toilet detergents, discoloration or damage may occur.

2. Scratches may occur during cleaning.
To avoid damage or scratches, please use a soft cloth for cleaning.


Scratch on the exterior

Problems may arise under the following circumstances:

1. If you clean the exterior using cleaning agents such as Thinner, Benzene, Lysol, or toilet detergents, discoloration or damage may occur.

2. Scratches may occur during cleaning.
To avoid damage or scratches, please use a soft cloth for cleaning.


Noise

There is an electric shock when sitting on the seat.

Problems may arise under the following circumstances:

1.If the deodorization function is turned on:
For models equipped with a deodorization feature, the sound you hear when seated is the deodorization fan operating.
Deodorization activates when seated and operates for 1 minute after the seat sensor no longers detects human skin.
While the power is on, you can press the drying button on the main control panel (side) to turn the deodorization function ON/OFF while not seated.


ETC

There is an electric shock when sitting on the seat.

Problems may arise under the following circumstances:

1.If the electrical outlet in the bathroom is not grounded:
Please check if the electrical outlet connected to the product is properly grounded.
For safety purposes, it is necessary to use an electrical outlet with a grounding terminal.


Purchasing parts

1. Please confirm the model name and purchase through our customer support center.
How to confirm the model name: Check the model name written on the back of the bidet unit.


How to clean the nozzle

The nozzle cleaning method is as follows:

External Nozzle Cleaning (Manual):
Press the nozzle cleaning button on the remote control or control bar to extend the nozzle.
Clean the exposed nozzle with a brush.
After cleaning, press the nozzle cleaning button again to retract the nozzle.

Internal Nozzle Cleaning (Automatic):
Our bidet automatically cleans the interior of the nozzle (posterior, feminine, turbo) once during nozzle usage, and once more after usage is completed.


Power/Operation 

The power is not turning on.

In the following cases, the device may not operate normally:

1. If the power is not coming into the outlet being used:
Please plug in another electronic device to confirm if power is coming in. If it operates normally, unplug the power cord of the dryer, wait for 1 minute, then plug it in again to reset the dryer.

2 .If the power is not coming into the dryer:
Press the power button to check if power is coming into the dryer.

3. If it doesn't operate when stepping onto the platform:
Our dryer automatically operates when detecting a weight of over 10kg. (For children weighing less than 10kg, please operate it manually. Manual mode: Press the power for more than 3 seconds without stepping onto the platform.)

4. If a child (weighing less than 10kg) has used it:
Please operate it in manual mode. (Manual mode: Press the power for more than 3 seconds without stepping onto the platform.)


The air isn't warm enough.

In the following cases, the device may not operate normally:

1.If the air temperature is set to COOL:
Please touch the wind temperature button on the control panel to change COOL to WARM.
(When using COOL, a white LED appears on the temperature gauge icon on the control panel; when using WARM, a red LED appears on the temperature gauge icon.)

2. If the air outlet on the platform is blocked:
Please remove any foreign objects or dust from the air outlet.

3. If the rear air inlet is blocked:
Please remove any foreign objects or dust from the rear air inlet.


The airflow is weak.

In the following cases, the device may not operate normally:

1. If the wind volume is set to LOW:
Please touch the wind volume button on the control panel to change LOW to HIGH.
(When using LOW, the wind volume icon on the control panel will not be illuminated; when using HIGH, a white LED will illuminate the airflow icon.)

2. If the air outlet on the platform is blocked:
Please remove any foreign objects or dust from the air outlet.

3. If a child (10-20kg) has used the device:
Please touch the airflow button on the control panel to change LOW to HIGH.
*When a child (10-20kg) uses the device, it will automatically start with a gentle breeze.

4. If the rear air inlet is blocked:
Please remove any foreign objects or dust from the rear air inlet.


The wind volume mode isn't changing.

In the following cases, the device may not operate normally:

1. If the dryer mode setting is incorrect:
Please touch the dryer mode button on the control panel to choose the desired airflow type.
(When using FOOT mode, the person icon on the control panel won't light up; when using BODY mode, a white LED will illuminate the person icon.)

2. If the air outlet on the platform is blocked:
Please remove any foreign objects or dust from the air outlet.


The scale isn't functioning properly.
The scale isn't accurate.

In the following cases, the device may not operate normally:

1.If the dryer isn't level:
Please adjust the dryer to be level.
(Using the dryer on cushioned surfaces like carpets may cause errors in weight measurement.)

2. If a child (weighing less than 10kg) has used the device:
Our dryer operates from 10kg and above, so it won't detect the weight of children weighing less than 10kg.

3. If the unit setting isn't correct:
Please change the unit setting.
Press and hold the SCALE button for 3 seconds to change the unit of the scale (kg, lb).


The control panel is flickering.

In the following cases, the device may not operate normally:

1. If "E01" is displayed on the display:
This indicates a leak detection issue. Tilt the product to release any trapped water and then use it.
(The dryer is an electrical appliance. While water may not easily penetrate inside, repeated spraying from various directions could lead to water ingress through the intake and air outlet, so please refrain from spraying water directly.)

2. If "E02" is displayed on the display:
This indicates a temperature sensor malfunction. Please contact the A/S center for assistance. (Related to ambient temperature)

3. If "C01" is displayed on the display:
This indicates a weight detection of 220kg. The allowable load for our dryer is between 10 and 220kg.


Noise 

The operational noise is loud.

In the following cases, the device may not operate normally:

1.If the wind volume is set to HIGH:
Please touch the airflow button on the control panel to change HIGH to LOW.

2. If the air outlet on the platform is blocked:
Please remove any foreign objects or dust from the air outlet.

3. If the rear air inlet is blocked:
Please remove any foreign objects or dust from the rear air inlet.


ETC 

There is an odor when using it.

In the following cases, the device may not operate normally:

1.If it's the first time using:
The smell is caused by the initial heating of the heater and is considered normal. (The odor should diminish gradually with continued use.)

2. If the rear air inlet is blocked:
Please remove any foreign objects or dust from the rear air inlet.

3. If the air outlet on the platform is blocked:
Please remove any foreign objects or dust from the air outlet.

4. If using in a place where smoke or odor occurs:
Please ventilate the area before using again.


Power/Operation

The power is not turning on.

In the following cases, the device may not operate normally:
1. Check the power outlet you are using:
Try plugging in another electronic device to verify if electricity is flowing into the outlet. If it operates normally, disconnect the air purifier's power cord for a minute before reconnecting it to reset the device.

2. Ensure the air purifier's power is on:
Press the power button to see if the air purifier turns on.

3. If you've moved the product:
Check the power cord to ensure it's properly connected. (It might have slightly come loose, so try reconnecting it securely.)
* Note: The power cord is designed to detach for safety reasons.

4. If the filter cover is detached:
Reattach the filter cover.
* If the filter cover is not properly secured, the status indicator will display E2, and the product will not operate.


The wind speed is weak.

In the following cases, the device may not operate normally:

1. If the filter packaging is not removed:
Please remove the protective film from the cypress wood filter and the plastic wrapping from the circular filter after purchasing the product.

2. If the filter is not correctly installed:
Ensure that the filter is properly installed before use.

3. If there is a lot of dust accumulated on the filter:
Dust buildup on the filter can result in increased noise levels. Please use a vacuum cleaner to remove the accumulated dust from the filter.

4. If the fan speed setting is in Auto mode or Sleep mode:
Change the fan speed setting to Manual mode or Cyclone mode before use.


The air quality indicator remains unchanged.

In the following cases, the device may not operate normally:

1. If the sensor is obstructed by a wall or obstacle:
Please ensure to leave a distance of at least 10cm at the rear and 20cm on each side when using.

2. If the dust sensor is heavily covered with dust:
Please clean the dust sensor.


E2 error is displayed.

In the following cases, the device may not operate normally:

1.If the filter cover is detached:
Please attach it properly.
* If the filter cover is not properly secured, the product will not operate, and an E2 error code will be displayed.


Sleep mode isn't working.

In the following cases, the device may not operate normally:
*Our air purifier switches to Sleep Mode based on sensor only during Auto Mode.

1. When the surrounding area is bright:
During Auto Mode operation, please darken the area around the light sensor.
* If the area around the light sensor remains dark after setting it to Auto Mode, it will switch to Sleep Mode after approximately 10 seconds.


Noise

The noise during operation is loud.

In the following cases, the device may not operate normally:

1. If the filter packaging is not removed:
Please remove the protective film from the cypress wood filter and the plastic wrapping from the circular filter after purchasing the product.

2. If there is a lot of dust accumulated on the filter:
Dust buildup on the filter can result in increased noise levels. Please use a vacuum cleaner to remove the accumulated dust from the filter.

3. If the fan speed setting is in Auto Mode or Cyclone Mode:
Adjust the fan speed setting to levels 1 to 3 before use.
*In Auto Mode, the fan speed adjusts automatically according to the level of air pollution, leading to variations in operational noise.


There is a noise that sounds like something is getting caught during operation.

In the following cases, the device may not operate normally:

1. If the appliance isn't level:
Please ensure it's placed on a flat surface. (Uneven floors may cause the appliance to tilt, leading to noise as the fan contacts the internal wall while attempting to maintain its rotation axis.)

2. If there are foreign substances in the air outlet or filter compartment:
Please the air outlet and filter compartment for any foreign substances and remove them.


Circular filter & Cypress wood filter

How do I install/remove the diffuser capsule?

1. Turn off the power and detach the cypress wood filter using the provided detachment hook.
2. Use a screwdriver to loosen the screws on the safety mesh.
3. Remove the safety mesh.
4. Detach the cover of the ventilation fan.
5. Remove the cover from the diffuser capsule.(Do not remove the transparent film)
6. Place the diffuser capsule into the ventilation fan and secure the cover.
7. Use a screwdriver to fasten the screws on the safety mesh.
8. Assemble the cypress wood filter to fit the exterior.


How often should the filter be replaced?

The replacement cycle for the circular HEPA filter is one year, and for the cypress wood filter, it is two years.
After turning on the power, the filter remaining indicator will display the remaining duration before the circular HEPA filter needs replacement for 5 seconds.


Even after the circular filter is replaced, the indicator displaying the remaining filter amount remains unchanged.

After replacing the filter, please reset the filter remaining indicator on the device.
Reset Method: Press the Auto button and Cyclone button simultaneously while the power is off.


I don't smell the scent of cypress wood.

Even if there is no scent from the cypress wood filter, its efficacy will last for 2 years.

* The cypress wood filter is a consumable item like the circular filter, so please replace it after the replacement period (2 years) has passed.
* If you desire the cypress wood scent, please purchase our diffuser capsule and install it.


The shape of the cypress wood filter is changing.

Our cypress wood filters are crafted from solid wood, which may exhibit scratches, dents, and knots.

Wood naturally expands in the summer as it absorbs moisture and contracts in the winter as it releases moisture. Over time, this process may result in size variations of up to 5mm or the occurrence of cracks in the wood.


ETC

The odor is coming from the air vent.

In the following cases, the device may not operate normally:

1.If there are foreign substances in the air outlet or filter compartment:
Please the air outlet and filter compartment for any foreign substances and remove them.

2. If the filter is heavily covered with dust:
An accumulation of dust on the filter can cause odors. Please use a vacuum cleaner to remove dust from the filter.

If the air purifier was previously used in the kitchen or a smoking area:
Filters are designed to absorb odors, so they might temporarily retain odors from previous usage. However, these odors will gradually diminish with time.
*Residual odors from previous locations may linger.


Power/Operation

The power is not turning on.

In the following cases, the device may not operate normally:
1. Check the power outlet you are using:
Try plugging in another electronic device to verify if electricity is flowing into the outlet. If it operates normally, disconnect the air purifier's power cord for a minute before reconnecting it to reset the device.

2. Ensure the air purifier's power is on:
Press the power button to see if the air purifier turns on.

3. If you've moved the product:
Check the power cord to ensure it's properly connected. (It might have slightly come loose, so try reconnecting it securely.)
* Note: The power cord is designed to detach for safety reasons.


The wind speed is weak.

In the following cases, the device may not operate normally:

1. If the filter packaging is not removed:
Please remove the protective film from the cypress wood filter and the plastic wrapping from the circular filter after purchasing the product.

2. If the filter is not correctly installed:
Ensure that the filter is properly installed before use.

3. If there is a lot of dust accumulated on the filter:
Dust buildup on the filter can result in increased noise levels. Please use a vacuum cleaner to remove the accumulated dust from the filter.

4. If the fan speed setting is in Auto mode or Sleep mode:
Change the fan speed setting to Manual mode or Cyclone mode before use.


Sleep mode isn't working.

In the following cases, the device may not operate normally:
*Our air purifier switches to Sleep Mode based on sensor only during Auto Mode.

1. When the surrounding area is bright:
During Auto Mode operation, please darken the area around the light sensor.
* After setting to Auto mode, if the area around the light sensor is dark, it will switch to Sleep & Eco mode after about 10 seconds.


Noise

The noise during operation is loud.

In the following cases, the device may not operate normally:

1. If the filter packaging is not removed:
Please remove the protective film from the cypress wood filter and the plastic wrapping from the circular filter after purchasing the product.

2. If there is a lot of dust accumulated on the filter:
Dust buildup on the filter can result in increased noise levels. Please use a vacuum cleaner to remove the accumulated dust from the filter.

3. If the fan speed setting is in Auto Mode or Cyclone Mode:
Adjust the fan speed setting to levels 1 to 3 before use.
*In Auto Mode, the fan speed adjusts automatically according to the level of air pollution, leading to variations in operational noise.


There is a noise that sounds like something is getting caught during operation.

In the following cases, the device may not operate normally:

1. Check the connection status of the product's legs.
Ensure that there are no incorrectly connected areas between the main body and the legs.

2. If the appliance isn't level:
Please ensure it's placed on a flat surface.
(Uneven floors may cause the appliance to tilt, leading to noise as the fan contacts the internal wall while attempting to maintain its rotation axis.)

3. If there are foreign substances in the air outlet or filter compartment:
Please the air outlet and filter compartment for any foreign substances and remove them.


Circular filter & Cypress wood filter

How do I install/remove the diffuser capsule?

1. Turn off the power and detach the cypress wood filter using the provided detachment hook.
2. Remove the safety mesh.
3. Remove the cover from the diffuser capsule.(Do not remove the transparent film)
4. Place the diffuser capsule into the ventilation fan and secure the cover.
5. Assemble the cypress wood filter to fit the exterior.


How often should the filter be replaced?

The replacement cycle for the circular HEPA filter is one year, and for the cypress wood filter, it is two years.


I don't smell the scent of cypress wood.

Even if there is no scent from the cypress wood filter, its efficacy will last for 2 years.

* The cypress wood filter is a consumable item like the circular filter, so please replace it after the replacement period (2 years) has passed.
* If you desire the cypress wood scent, please purchase our diffuser capsule and install it.


The shape of the cypress wood filter is changing.

Our cypress wood filters are crafted from solid wood, which may exhibit scratches, dents, and knots.

Wood naturally expands in the summer as it absorbs moisture and contracts in the winter as it releases moisture. Over time, this process may result in size variations of up to 1-2 mm or the occurrence of cracks in the wood.


ETC

The odor is coming from the air vent.

In the following cases, the device may not operate normally:

1.If there are foreign substances in the air outlet or filter compartment:
Please the air outlet and filter compartment for any foreign substances and remove them.

2. If the filter is heavily covered with dust:
An accumulation of dust on the filter can cause odors. Please use a vacuum cleaner to remove dust from the filter.

3. If the air purifier was previously used in the kitchen or a smoking area:
Filters are designed to absorb odors, so they might temporarily retain odors from previous usage. However, these odors will gradually diminish with time.
*Residual odors from previous locations may linger.


Power/Operation

The power is not turning on.

In the following cases, the device may not operate normally:

1. Check the vehicle's USB socket.
Ensure that other USB devices connected to the vehicle's USB socket are functioning properly.

2. Check the USB cable.
Verify the connection between the product and the USB cable.
* Please use the USB cable provided with the product.

3. If the product is turned off.
Press and hold the power button for 3 seconds to turn on the power.
* You can press and hold the power button for 3 seconds to turn the power on/off.


The wind speed is weak.

In the following cases, the device may not operate normally:

1. If the filter packaging is not removed:
Please remove the protective film from the cypress wood filter after purchasing the product.

2. If the filter is not correctly installed:
Ensure that the filter is properly installed before use.

3. If there is a lot of dust accumulated on the filter:
Dust buildup on the filter can result in increased noise levels. Please use a vacuum cleaner to remove the accumulated dust from the filter.

4. If the fan speed is set to level 1:
Please adjust the fan speed to levels 2-3 before use.


Circular filter & Cypress wood filter

How do I install/remove the diffuser capsule?

1. Rotate the bottom part of the main body to detach the filter.
2. Remove the cover from the diffuser capsule.(Do not remove the transparent film)
3. Place the diffuser capsule into the holder.
4. Attach the holder to the top part of the filter.
5. Insert the filter into the bottom part of the main body and rotate to secure it.


How often should the filter be replaced?

The replacement cycle for the circular HEPA filter is one year.


I don't smell the scent of cypress wood.

Even if there is no scent from the cypress wood filter, its efficacy will last.-> 2년 지웠어요

* If you desire the cypress wood scent, please purchase our diffuser capsule and install it.


The shape of the cypress wood filter is changing.

Our cypress wood filters are crafted from solid wood, which may exhibit scratches, dents, and knots.

Wood naturally expands in the summer as it absorbs moisture and contracts in the winter as it releases moisture. Over time, this process may result in size variations of up to 1-2 mm or the occurrence of cracks in the wood.


ETC

The odor is coming from the air vent.

In the following cases, the device may not operate normally:

1.If there are foreign substances in the air outlet or filter compartment:
Please the air outlet and filter compartment for any foreign substances and remove them.

2. If the filter is heavily covered with dust:
An accumulation of dust on the filter can cause odors. Please use a vacuum cleaner to remove dust from the filter.

3. If the air purifier was previously used in the kitchen or a smoking area:
Filters are designed to absorb odors, so they might temporarily retain odors from previous usage. However, these odors will gradually diminish with time.
*Residual odors from previous locations may linger.


Q&A


Flushing Issue

Excessive water splashes during flushing

The flushing may not operate properly under the following condition:

1. If the water pressure in the bathroom is high:
Please adjust the water pressure using the valve connected to the bidet's water supply hose.
(Turn clockwise to adjust the water pressure.)


Flushing does not work

The flushing may not operate properly under the following conditions:

1. If the toilet bowl is clogged:
Press the jet button on the manual flush button to check if the toilet bowl is clogged.
(If clogged, there will be no water flow, only bubbles.)

2. If the water pressure in the bathroom is low:
2-1. Adjust the water pressure using the valve connected to the bidet's water supply hose.
(Turn counterclockwise to fully open the valve.)
2-2. Remove the pressure reduction valve for flushing.
(Pressure reduction valve removal guide)

3. If water is being used elsewhere simultaneously:
Our bidet operates directly from the customer's water pressure. When water is being used elsewhere (washing machine, sink, shower), it may result in reduced water pressure, affecting drainage.

4. If the original water pressure is low:
Check the water pressure at your home.
(If the pressure is less than 1.5kgf/㎠, drainage may not be efficient.)
(To confirm the minimum required water pressure: Open the water supply valve fully and collect water in a container for 10 seconds, then check the quantity (3.5 liters).)

5. If a dual valve is installed:
Remove the dual valve and use our bidet's water supply hose.


Remote not working

Remote not working

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If power is not supplied to the bidet:
Check if the POWER LED on the main display panel is lit.

3. If the remote control ran out of battery:
Press the buttons on the remote control to see if the LED light on the remote control lights up. If the LED light is off, replace the batteries with new ones.

4. If there is an issue with the remote control buttons:
Turn on the camera function of your mobile phone and aim it at the remote control receiver.
While looking at your phone's screen, repeatedly press the malfunctioning buttons on the remote control.
(If only certain buttons do not emit light, there may be an issue with the remote control.)


Remote not powered

Problems may arise under the following circumstances:

1. If the remote control ran out of battery:
Press the buttons on the remote control to see if the LED light on the remote control lights up. If the LED light is off, replace the batteries with new ones.

2. If there is an issue with the remote control buttons:
Turn on the camera function of your mobile phone and aim it at the remote control receiver.
While looking at your phone's screen, repeatedly press the malfunctioning buttons on the remote control.
(If only certain buttons do not emit light, there may be an issue with the remote control.)


Remote not working even though there is a beep sound

Problems may arise under the following circumstances:

1. If the seat sensor does not detect human skin:
How to check if the seat sensor is operational
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
After the nozzle comes out, please ensure that the nozzle goes in when you make skin contact with the seat sensor (located on the left thigh area).

* Our bidet requires seat sensor (located on the left thigh area) to detect human skin in order for all nozzle function to operate.


All other functions operate except stop function
>Only specific function is not working

Problems may arise under the following circumstances:

1. If there is an issue with the remote control buttons:
Turn on the camera function of your mobile phone and aim it at the remote control receiver.
While looking at your phone's screen, repeatedly press the malfunctioning buttons on the remote control.
(If only certain buttons do not emit light, there may be an issue with the remote control.)


Function malfunctioning

Bidet does not power on

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If power is not supplied to the bidet:
Check if the POWER LED on the main display panel is lit.


Seat temperature does not change even after setting the temperature.
> seat is not warm.

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the bidet seat temperature setting is at level 0:
Adjust the bidet seat temperature to levels 1 to 3 using the remote control before use.
(Please confirm the reception sound (beep) from the bidet when adjusting the seat temperature.)
(It takes approximately 5 minutes to warm up the seat. Please wait for about 5 minutes after setting the seat temperature before use.)

3. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


The seat feels lukewarm.
>The seat is not warm.

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the bidet seat temperature setting is at level 0:
Adjust the bidet seat temperature to levels 1 to 3 using the remote control before use.
(Please confirm the reception sound (beep) from the bidet when adjusting the seat temperature.)
(It takes approximately 5 minutes to warm up the seat. Please wait for about 5 minutes after setting the seat temperature before use.)

3. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


Sometimes the seat feels cold.
>The seat is not staying warm.

Problems may arise under the following circumstances:

1. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


The seat is always warm even without setting temperature.

Problems may arise under the following circumstances:

1. If the seat temperature setting is at level 3:
Adjust the seat temperature to levels 0 to 1 using the remote control before use.
(Please confirm the beep sound from the bidet when adjusting the seat temperature.)


Sometimes the circuit breaker trips.

Problems may arise under the following circumstances:

1. If the power cord is not properly connected:
Ensure that the power plug is securely inserted into the outlet, as loose connections can cause issues.
(Be sure to use an AC 120V~, 60Hz outlet with proper grounding.)

* TCB-090SA/RTB-090WA/PB-707S/PB-101S : 703W
* TCB-8100W/TCB-8100B : 1180W

2. If there are electrical issues with the bathroom outlet:
Disconnect the bidet power plug from the outlet and plug in another electronic device such as a hairdryer to see if the circuit breaker trips.
→ If the circuit breaker trips, contact the building management or an electrician to inspect the electrical outlet.


The drying function is not warm.
>The drying is not warm

Problems may arise under the following circumstances:

1. If there is no power in the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the drying temperature setting is at level 0:
Adjust the drying temperature to levels 1 to 3 using the remote control before use.
* If the drying temperature is set at level 0 or 1, you may experience weak drying air.
* If the air speed is too strong, it may cause odor to rise, so we have not set the air speed to strong in order to prevent odor from rising.


Flushing sometimes does not work

Problems may arise under the following circumstances:

1. If the automatic flushing setting is OFF;
Please turn on the automatic flushing function using the remote control.

2. If the seat sensor does not detect human skin:
How to check if the seat sensor is operational
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
After the nozzle comes out, please ensure that the nozzle goes in when you make skin contact with the seat sensor (located on the left thigh area).

* Our bidet requires seat sensor (located on the left thigh area) to detect human skin in order for all nozzle function to operate.


Flushing does not work

Problems may arise under the following circumstances:

1. If the automatic flushing setting is OFF;
Please turn on the automatic flushing function using the remote control.

2. If the seat sensor does not detect human skin:
How to check if the seat sensor is operational
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
After the nozzle comes out, please ensure that the nozzle goes in when you make skin contact with the seat sensor (located on the left thigh area).

* Our bidet requires seat sensor (located on the left thigh area) to detect human skin in order for all nozzle function to operate.


External appearance defect

Crack on the exterior

Problems may arise under the following circumstances:

1. If you clean the exterior using cleaning agents such as Thinner, Benzene, Lysol, or toilet detergents, discoloration or damage may occur.

2. Scratches may occur during cleaning.
To avoid damage or scratches, please use a soft cloth for cleaning.


Scratch on the exterior

Problems may arise under the following circumstances:

1. If you clean the exterior using cleaning agents such as Thinner, Benzene, Lysol, or toilet detergents, discoloration or damage may occur.

2. Scratches may occur during cleaning.
To avoid damage or scratches, please use a soft cloth for cleaning.


Seat not staying upright
>Fixture exists behind the seat cover

Problems may arise under the following circumstances:

1. If there is a narrow gap between the seat cover and any fixtures behind the seat cover preventing the seat cover to fully open,
Please use the offset flange, pull it forward, and reinstall the toilet bowl.
(If the gap between the bidet and any fixtures behind the seat cover is narrow, the bidet's seat cover and seat may not stay up in place.)


The edge strip of the seat cover is peeling off.

Problems may arise under the following circumstances:

1. In cases of high or low external temperatures,
The bidet seat cover's adhesive strip may occasionally come loose. This is due to external temperature fluctuations and not a product defect. Simply press the strip back into place manually to reattach it.


Toilet bowl rust formation

Problems may arise under the following circumstances:

1. If not in use for an extended period,
After flushing, use soap and an abrasive cleaner to remove any residue.
Extended periods of non-use may cause iron deposits to settle and rust to form.


When sitting on the seat and urinating, urine splashes.

Problems may arise under the following circumstances:

1. When sitting on the seat and using it from the outside;
Please sit as far back inside the bidet as possible before use.


Nozzle Not operating

The nozzle water pressure is weak.

Problems may arise under the following circumstances:

1. If the water supply valve is not fully open (if the water pressure at your home is less than 1 kgf/㎠):
Please fully open the valve connected to the bidet hose.
- Check the water pressure at your home. (If the water pressure is less than 1 kgf/㎠, the water sprayed from the nozzle may be reduced.)

2. If the nozzle water pressure setting is at level 1:
Adjust the water pressure using the remote control before use.

3. If there is debris in the mesh:
Detach the water supply hose, clean the mesh, and then use it. (Refer to the mesh cleaning guide)

4. If the bidet water supply hose is bent or the water supply hose assembly is incorrect:
Check if the water supply hose is tangled or bent before use.
Detach the water supply hose and check the rubber packing on the hose before use. (Bidet hose check guide)


The nozzle comes out, but no water comes out.

Problems may arise under the following circumstances:

1. If the water supply valve is not fully open (if the water pressure at your home is less than 1 kgf/㎠):
Please fully open the valve connected to the bidet hose.
- Check the water pressure at your home. (If the water pressure is less than 1 kgf/㎠, the water sprayed from the nozzle may be reduced.)

2. If the nozzle water pressure setting is at level 1:
Adjust the water pressure using the remote control before use.

3. If there is debris in the mesh:
Detach the water supply hose, clean the mesh, and then use it. (Refer to the mesh cleaning guide)

4. If the bidet water supply hose is bent or the water supply hose assembly is incorrect:
Check if the water supply hose is tangled or bent before use.
Detach the water supply hose and check the rubber packing on the hose before use. (Bidet hose check guide)


The nozzle does not come out / does not retract.

Problems may arise under the following circumstances:

1. If water is not supplied to the bidet:
Fully open the valve connected to the bidet hose, then unplug the bidet power cord for 1 minute before plugging it back in to supply water to the bidet.

2. If there is a reception failure in the remote control:
Press the LED button on the remote control to verify if the bidet is operational.

3. If the seat sensor does not detect human skin:
How to check if the seat sensor is operational
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
After the nozzle comes out, please ensure that the nozzle goes in when you make skin contact with the seat sensor (located on the left thigh area).

* Our bidet requires seat sensor (located on the left thigh area) to detect human skin in order for all nozzle function to operate.


The nozzle does not dispense warm water.
>The water is not warm.

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the warm water temperature setting is at level 0:
Adjust the warm water temperature to levels 1 to 3 using the remote control before use.
(It takes approximately 3 to 4 minutes to heat the water. Please wait for 3 to 4 minutes after setting the warm water temperature before use.)

3. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


Flushing function works but the nozzle function does not.

Problems may arise under the following circumstances:

1. If the seat sensor does not detect human skin:
How to check if the seat sensor is operational
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
After the nozzle comes out, please ensure that the nozzle goes in when you make skin contact with the seat sensor (located on the left thigh area).

* Our bidet requires seat sensor (located on the left thigh area) to detect human skin in order for all nozzle function to operate.


Leakage

Leakage near the high-pressure hose.

Problems may arise under the following circumstances:

1. If the water supply hose connection is not properly done:
Close the valve connected to the bidet's water supply hose, then disassemble and reassemble the bidet and water supply hose to ensure proper connection. Check for any leakage afterwards.


Water drips slowly from the right side of the bidet nozzle.

Problems may arise under the following circumstances:

1. If the water pressure at your home is above 6kgf/㎠
If the water pressure at your home is above 6kgf/cm2, it may cause minor leakage. Please lower the water pressure to below 6kgf/cm2 before use.


There is leakage from the bottom of the bidet unit.

Problems may arise under the following circumstances:

1. If the water supply hose is not properly connected:
Close the valve connected to the bidet's water supply hose and reassemble the bidet and the water supply hose. Then check for any leaks.

2. If the connection between the upper bidet unit and the ceramic bowl unit is not properly established:
Reassemble the upper bidet unit and the ceramic bowl unit, then check for any leaks.


Auto Open /Close

Auto open and close function not working

Problems may arise under the following circumstances:

1. If the automatic open/close setting is OFF;
Please set it to ON using the remote control and then check the function. (When the automatic open/close setting is ON, only the seat cover will open/close when a person or object is detected in front of the bidet. If there is no one present, it will automatically close after about 90 seconds.)


When the AUTO open/close function is activated, there is a buzzing noise.

Problems may arise under the following circumstances:

1. If you forcibly open or close the seat or seat cover
Please open both the seat and seat cover, unplug the bidet power cord for 1 minute, and then plug it back in to reset the bidet. (Forcibly opening or closing without using the remote control buttons may cause the automatic open/close function to malfunction.)


When pressing the seat open/close button, it doesn't fully open, and closes instead.

Problems may arise under the following circumstances:

1. If you forcibly open or close the seat or seat cover
Please open both the seat and seat cover, unplug the bidet power cord for 1 minute, and then plug it back in to reset the bidet. (Forcibly opening or closing without using the remote control buttons may cause the automatic open/close function to malfunction.)


The seat cover sometimes opens and closes on its own

Problems may arise under the following circumstances:

1. If there are moving objects around the bidet;
Please remove them from the vicinity of the bidet.
(If moving objects are detected after the automatic opening/closing setting, the seat cover will open and close after 90 seconds.)


Noise

There is noise when sitting on the seat.

Problems may arise under the following circumstances:

1.If the deodorization function is turned on:
For models equipped with a deodorization feature, the sound you hear when seated is the deodorization fan operating.
Deodorization activates when seated and operates for 1 minute after the seat sensor no longers detects human skin.


After flushing, there is a dripping sound of water

Problems may arise under the following circumstances:

1.If there is noise coming from the front of the bidet:
It is the sound of residual water being discharged, typically occurring for around 30 seconds after flushing.

2. If there is noise coming from the back of the bidet:
It is the sound of residual water flowing over after flushing.


ETC

There is no water leakage, but there is an odor

Problems may arise under the following circumstances:

1. If the plumbing and toilet bowl are not connected properly:
Check the connection between the flange, wax ring, and the toilet bowl's drainage hole.
(Installation may not have been done correctly.)


When flushing, foam is generated, and water spurts out.

Problems may arise under the following circumstances:

1. If there is foreign matter inside the toilet;
Please refrain from disposing of foreign objects such as wet wipes or sanitary pads inside the bidet. Dispose of them in a trash bin instead. Foreign objects can cause clogging and water drainage issues.


There is an electric shock when sitting on the seat.

Problems may arise under the following circumstances:

1.If the electrical outlet in the bathroom is not grounded:
Please check if the electrical outlet connected to the product is properly grounded.
For safety purposes, it is necessary to use an electrical outlet with a grounding terminal.


Missing Parts

1. Please confirm the model name and purchase through our customer support center.
How to confirm the model name: Check the model name written on the back of the bidet unit.


Remote not working

Remote not working

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If power is not supplied to the bidet:
Check if the POWER LED on the main display panel is lit.

3. If the remote control's batteries ran out of battery:
Press the buttons on the remote control to see if the LED light on the remote control lights up. If the LED light is off, replace the batteries with new ones.

4. If there is an issue with the remote control buttons:
Turn on the camera function of your mobile phone and aim it at the remote control receiver.
While looking at your phone's screen, repeatedly press the malfunctioning buttons on the remote control.
(If only certain buttons do not emit light, there may be an issue with the remote control.)


Remote not powered

Problems may arise under the following circumstances:

1. If the remote control's batteries ran out of battery:
Press the buttons on the remote control to see if the LED light on the remote control lights up. If the LED light is off, replace the batteries with new ones.

2. If there is an issue with the remote control buttons:
Turn on the camera function of your mobile phone and aim it at the remote control receiver.
While looking at your phone's screen, repeatedly press the malfunctioning buttons on the remote control.
(If only certain buttons do not emit light, there may be an issue with the remote control.)


Remote not working even though there is a beep sound

Problems may arise under the following circumstances:

1. If the seat sensor does not detect human skin:
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
(Our bidet requires seat sensor(located under your left thigh area) to detect human skin in order for all nozzle function to operate.)


All other functions operate except stop function
>Only specific function is not working

Problems may arise under the following circumstances:

1. If there is an issue with the remote control buttons:
Turn on the camera function of your mobile phone and aim it at the remote control receiver.
While looking at your phone's screen, repeatedly press the malfunctioning buttons on the remote control.
(If only certain buttons do not emit light, there may be an issue with the remote control.)


Function malfunctioning

Bidet does not power on

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If power is not supplied to the bidet:
Check if the POWER LED on the main display panel is lit.


Seat temperature does not change even after setting up the temperature.
> seat is not warm.

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the bidet seat temperature setting is at level 0:
Adjust the bidet seat temperature to levels 1 to 3 using the remote control or side control panel before use.
(Please confirm the reception sound (beep) from the bidet when adjusting the seat temperature.)
(It takes approximately 5 minutes to warm up the seat. Please wait for about 5 minutes after setting the seat temperature before use.)

3. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


The seat feels lukewarm.
>The seat is not warm.

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the bidet seat temperature setting is at level 0:
Adjust the bidet seat temperature to levels 1 to 3 using the remote control or side control panel before use.
(Please confirm the reception sound (beep) from the bidet when adjusting the seat temperature.)
(It takes approximately 5 minutes to warm up the seat. Please wait for about 5 minutes after setting the seat temperature before use.)

3. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


Sometimes the seat feels cold.
>The seat is not staying warm.

Problems may arise under the following circumstances:

1. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


The seat is always warm even without temperature setting.

Problems may arise under the following circumstances:

1. If the seat temperature setting is at level 3:
Adjust the seat temperature to levels 0 to 1 using the remote control or side control panel before use.
(Please confirm the beep sound from the bidet when adjusting the seat temperature.)


Sometimes the circuit breaker trips.

Problems may arise under the following circumstances:

1. If the power cord is not properly connected:
Ensure that the power plug is securely inserted into the outlet, as loose connections can cause issues.
(Be sure to use an AC 120~, 60Hz outlet with proper grounding.)
* VB-6000 / VB-4000 / VB-3000 : 1200W

2. If there are electrical issues with the bathroom outlet:
Disconnect the bidet power plug from the outlet and plug in another electronic device such as a hairdryer to see if the circuit breaker trips.
→ If the circuit breaker trips, contact the building management or an electrician to inspect the electrical outlet.


The drying function is not warm.
>The drying is not warm.

Problems may arise under the following circumstances:

1. If there is no power in the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the drying temperature setting is at level 0:
Adjust the drying temperature to levels 1 to 3 using the remote control or side control panel before use.
* If the drying temperature is set at level 0 or 1, you may experience weak drying air.
* If the air speed is too strong, it may cause odor to rise, so we have not set the air speed to strong in order to prevent odor from rising.


Nozzle Not operating

The nozzle water pressure is weak.

Problems may arise under the following circumstances:

1. If the water supply valve is not fully open (if the water pressure at your home is less than 1 kgf/㎠):
Please fully open the valve connected to the bidet hose.
- Check the water pressure at your home. (If the water pressure is less than 1 kgf/㎠, the water sprayed from the nozzle may be reduced.)

2. If the nozzle water pressure setting is at level 1:
Adjust the water pressure using the remote control or side control panel before use.

3. If there is debris in the mesh:
Detach the water supply hose, clean the mesh, and then use it. (Refer to the mesh cleaning guide)

4. If the bidet water supply hose is bent or the water supply hose assembly is incorrect:
Check if the water supply hose is tangled or bent before use.
Detach the water supply hose and check the rubber packing on the hose before use. (Bidet hose check guide)


The nozzle comes out, but no water comes out.

Problems may arise under the following circumstances:

1. If the water supply valve is not fully open (if the water pressure at your home is less than 1 kgf/㎠):
Please fully open the valve connected to the bidet hose.
- Check the water pressure at your home. (If the water pressure is less than 1 kgf/㎠, the water sprayed from the nozzle may be reduced.)

2. If the nozzle water pressure setting is at level 1:
Adjust the water pressure using the remote control or side control panel before use.

3. If there is debris in the mesh:
Detach the water supply hose, clean the mesh, and then use it. (Refer to the mesh cleaning guide)

4. If the bidet water supply hose is bent or the water supply hose assembly is incorrect:
Check if the water supply hose is tangled or bent before use.
Detach the water supply hose and check the rubber packing on the hose before use. (Bidet hose check guide)


The nozzle does not come out / does not retract.

Problems may arise under the following circumstances:

1. If water is not supplied to the bidet:
Fully open the valve connected to the bidet hose, then unplug the bidet power cord for 1 minute before plugging it back in to supply water to the bidet.

2. If there is a reception failure in the remote control or side control panel:
Press the LED button on the remote control or side control panel to verify if the bidet is operational.

3. If the seat sensor does not detect human skin:
Press the nozzle cleaning button to check if the nozzle comes out (if the nozzle comes out, it is functioning properly).
Our bidet requires seat sensor(located under your left thigh area) to detect human skin in order for all nozzle function to operate.


The nozzle does not dispense warm water.
>The water is not warm.

Problems may arise under the following circumstances:

1. If power is not supplied to the bathroom:
Check if power is coming by plugging in electronic devices like a hairdryer. If power is supplied, unplug the bidet's power cord, wait for 1 minute, and then plug it back in to reset the bidet.

2. If the warm water temperature setting is at level 0:
Adjust the warm water temperature to levels 1 to 3 using the remote control or side control panel before use.
(It takes approximately 3 to 4 minutes to heat the water. Please wait for 3 to 4 minutes after setting the warm water temperature before use.)

3. If the power-saving mode is activated:
If you have enabled the power-saving mode, please deactivate it.
(Power-saving mode explanation/deactivation guide)


Leakage

Leakage near the high-pressure hose.

Problems may arise under the following circumstances:

1. If the water supply hose connection is not properly done:
Close the valve connected to the bidet's water supply hose, then disassemble and reassemble the bidet and water supply hose to ensure proper connection. Check for any leakage afterwards.


Water drips slowly from the right side of the bidet nozzle.

Problems may arise under the following circumstances:

1. If the water pressure at your home is above 6kgf/㎠
If the water pressure at your home is above 6kgf/cm2, it may cause minor leakage. Please lower the water pressure to below 6kgf/cm2 before use.


There is leakage from the bottom of the bidet unit.

Problems may arise under the following circumstances:

1. Check the bottom of the bidet after removing it to inspect the water drainage bolt is open.
(Refer to the bidet removal guide and the guide on how to secure the water drainage bolt.)


External appearance defect

Crack on the exterior

Problems may arise under the following circumstances:

1. If you clean the exterior using cleaning agents such as Thinner, Benzene, Lysol, or toilet detergents, discoloration or damage may occur.

2. Scratches may occur during cleaning.
To avoid damage or scratches, please use a soft cloth for cleaning.


Scratch on the exterior

Problems may arise under the following circumstances:

1. If you clean the exterior using cleaning agents such as Thinner, Benzene, Lysol, or toilet detergents, discoloration or damage may occur.

2. Scratches may occur during cleaning.
To avoid damage or scratches, please use a soft cloth for cleaning.


Noise

There is an electric shock when sitting on the seat.

Problems may arise under the following circumstances:

1.If the deodorization function is turned on:
For models equipped with a deodorization feature, the sound you hear when seated is the deodorization fan operating.
Deodorization activates when seated and operates for 1 minute after the seat sensor no longers detects human skin.
While the power is on, you can press the drying button on the main control panel (side) to turn the deodorization function ON/OFF while not seated.


ETC

There is an electric shock when sitting on the seat.

Problems may arise under the following circumstances:

1.If the electrical outlet in the bathroom is not grounded:
Please check if the electrical outlet connected to the product is properly grounded.
For safety purposes, it is necessary to use an electrical outlet with a grounding terminal.


Purchasing parts

1. Please confirm the model name and purchase through our customer support center.
How to confirm the model name: Check the model name written on the back of the bidet unit.


How to clean the nozzle

The nozzle cleaning method is as follows:

External Nozzle Cleaning (Manual):
Press the nozzle cleaning button on the remote control or control bar to extend the nozzle.
Clean the exposed nozzle with a brush.
After cleaning, press the nozzle cleaning button again to retract the nozzle.

Internal Nozzle Cleaning (Automatic):
Our bidet automatically cleans the interior of the nozzle (posterior, feminine, turbo) once during nozzle usage, and once more after usage is completed.


Power/Operation 

The power is not turning on.

In the following cases, the device may not operate normally:

1. If the power is not coming into the outlet being used:
Please plug in another electronic device to confirm if power is coming in. If it operates normally, unplug the power cord of the dryer, wait for 1 minute, then plug it in again to reset the dryer.

2 .If the power is not coming into the dryer:
Press the power button to check if power is coming into the dryer.

3. If it doesn't operate when stepping onto the platform:
Our dryer automatically operates when detecting a weight of over 10kg. (For children weighing less than 10kg, please operate it manually. Manual mode: Press the power for more than 3 seconds without stepping onto the platform.)

4. If a child (weighing less than 10kg) has used it:
Please operate it in manual mode. (Manual mode: Press the power for more than 3 seconds without stepping onto the platform.)


The air isn't warm enough.

In the following cases, the device may not operate normally:

1.If the air temperature is set to COOL:
Please touch the wind temperature button on the control panel to change COOL to WARM.
(When using COOL, a white LED appears on the temperature gauge icon on the control panel; when using WARM, a red LED appears on the temperature gauge icon.)

2. If the air outlet on the platform is blocked:
Please remove any foreign objects or dust from the air outlet.

3. If the rear air inlet is blocked:
Please remove any foreign objects or dust from the rear air inlet.


The airflow is weak.

In the following cases, the device may not operate normally:

1. If the wind volume is set to LOW:
Please touch the wind volume button on the control panel to change LOW to HIGH.
(When using LOW, the wind volume icon on the control panel will not be illuminated; when using HIGH, a white LED will illuminate the airflow icon.)

2. If the air outlet on the platform is blocked:
Please remove any foreign objects or dust from the air outlet.

3. If a child (10-20kg) has used the device:
Please touch the airflow button on the control panel to change LOW to HIGH.
*When a child (10-20kg) uses the device, it will automatically start with a gentle breeze.

4. If the rear air inlet is blocked:
Please remove any foreign objects or dust from the rear air inlet.


The wind volume mode isn't changing.

In the following cases, the device may not operate normally:

1. If the dryer mode setting is incorrect:
Please touch the dryer mode button on the control panel to choose the desired airflow type.
(When using FOOT mode, the person icon on the control panel won't light up; when using BODY mode, a white LED will illuminate the person icon.)

2. If the air outlet on the platform is blocked:
Please remove any foreign objects or dust from the air outlet.


The scale isn't functioning properly.
The scale isn't accurate.

In the following cases, the device may not operate normally:

1.If the dryer isn't level:
Please adjust the dryer to be level.
(Using the dryer on cushioned surfaces like carpets may cause errors in weight measurement.)

2. If a child (weighing less than 10kg) has used the device:
Our dryer operates from 10kg and above, so it won't detect the weight of children weighing less than 10kg.

3. If the unit setting isn't correct:
Please change the unit setting.
Press and hold the SCALE button for 3 seconds to change the unit of the scale (kg, lb).


The control panel is flickering.

In the following cases, the device may not operate normally:

1. If "E01" is displayed on the display:
This indicates a leak detection issue. Tilt the product to release any trapped water and then use it.
(The dryer is an electrical appliance. While water may not easily penetrate inside, repeated spraying from various directions could lead to water ingress through the intake and air outlet, so please refrain from spraying water directly.)

2. If "E02" is displayed on the display:
This indicates a temperature sensor malfunction. Please contact the A/S center for assistance. (Related to ambient temperature)

3. If "C01" is displayed on the display:
This indicates a weight detection of 220kg. The allowable load for our dryer is between 10 and 220kg.


Noise 

The operational noise is loud.

In the following cases, the device may not operate normally:

1.If the wind volume is set to HIGH:
Please touch the airflow button on the control panel to change HIGH to LOW.

2. If the air outlet on the platform is blocked:
Please remove any foreign objects or dust from the air outlet.

3. If the rear air inlet is blocked:
Please remove any foreign objects or dust from the rear air inlet.


ETC 

There is an odor when using it.

In the following cases, the device may not operate normally:

1.If it's the first time using:
The smell is caused by the initial heating of the heater and is considered normal. (The odor should diminish gradually with continued use.)

2. If the rear air inlet is blocked:
Please remove any foreign objects or dust from the rear air inlet.

3. If the air outlet on the platform is blocked:
Please remove any foreign objects or dust from the air outlet.

4. If using in a place where smoke or odor occurs:
Please ventilate the area before using again.


Power/Operation

The power is not turning on.

In the following cases, the device may not operate normally:
1. Check the power outlet you are using:
Try plugging in another electronic device to verify if electricity is flowing into the outlet. If it operates normally, disconnect the air purifier's power cord for a minute before reconnecting it to reset the device.

2. Ensure the air purifier's power is on:
Press the power button to see if the air purifier turns on.

3. If you've moved the product:
Check the power cord to ensure it's properly connected. (It might have slightly come loose, so try reconnecting it securely.)
* Note: The power cord is designed to detach for safety reasons.

4. If the filter cover is detached:
Reattach the filter cover.
* If the filter cover is not properly secured, the status indicator will display E2, and the product will not operate.


The wind speed is weak.

In the following cases, the device may not operate normally:

1. If the filter packaging is not removed:
Please remove the protective film from the cypress wood filter and the plastic wrapping from the circular filter after purchasing the product.

2. If the filter is not correctly installed:
Ensure that the filter is properly installed before use.

3. If there is a lot of dust accumulated on the filter:
Dust buildup on the filter can result in increased noise levels. Please use a vacuum cleaner to remove the accumulated dust from the filter.

4. If the fan speed setting is in Auto mode or Sleep mode:
Change the fan speed setting to Manual mode or Cyclone mode before use.


The air quality indicator remains unchanged.

In the following cases, the device may not operate normally:

1. If the sensor is obstructed by a wall or obstacle:
Please ensure to leave a distance of at least 10cm at the rear and 20cm on each side when using.

2. If the dust sensor is heavily covered with dust:
Please clean the dust sensor.


E2 error is displayed.

In the following cases, the device may not operate normally:

1.If the filter cover is detached:
Please attach it properly.
* If the filter cover is not properly secured, the product will not operate, and an E2 error code will be displayed.


Sleep mode isn't working.

In the following cases, the device may not operate normally:
*Our air purifier switches to Sleep Mode based on sensor only during Auto Mode.

1. When the surrounding area is bright:
During Auto Mode operation, please darken the area around the light sensor.
* If the area around the light sensor remains dark after setting it to Auto Mode, it will switch to Sleep Mode after approximately 10 seconds.


Noise

The noise during operation is loud.

In the following cases, the device may not operate normally:

1. If the filter packaging is not removed:
Please remove the protective film from the cypress wood filter and the plastic wrapping from the circular filter after purchasing the product.

2. If there is a lot of dust accumulated on the filter:
Dust buildup on the filter can result in increased noise levels. Please use a vacuum cleaner to remove the accumulated dust from the filter.

3. If the fan speed setting is in Auto Mode or Cyclone Mode:
Adjust the fan speed setting to levels 1 to 3 before use.
*In Auto Mode, the fan speed adjusts automatically according to the level of air pollution, leading to variations in operational noise.


There is a noise that sounds like something is getting caught during operation.

In the following cases, the device may not operate normally:

1. If the appliance isn't level:
Please ensure it's placed on a flat surface. (Uneven floors may cause the appliance to tilt, leading to noise as the fan contacts the internal wall while attempting to maintain its rotation axis.)

2. If there are foreign substances in the air outlet or filter compartment:
Please the air outlet and filter compartment for any foreign substances and remove them.


Circular filter & Cypress wood filter

How do I install/remove the diffuser capsule?

1. Turn off the power and detach the cypress wood filter using the provided detachment hook.
2. Use a screwdriver to loosen the screws on the safety mesh.
3. Remove the safety mesh.
4. Detach the cover of the ventilation fan.
5. Remove the cover from the diffuser capsule.(Do not remove the transparent film)
6. Place the diffuser capsule into the ventilation fan and secure the cover.
7. Use a screwdriver to fasten the screws on the safety mesh.
8. Assemble the cypress wood filter to fit the exterior.


How often should the filter be replaced?

The replacement cycle for the circular HEPA filter is one year, and for the cypress wood filter, it is two years.
After turning on the power, the filter remaining indicator will display the remaining duration before the circular HEPA filter needs replacement for 5 seconds.


Even after the circular filter is replaced, the indicator displaying the remaining filter amount remains unchanged.

After replacing the filter, please reset the filter remaining indicator on the device.
Reset Method: Press the Auto button and Cyclone button simultaneously while the power is off.


I don't smell the scent of cypress wood.

Even if there is no scent from the cypress wood filter, its efficacy will last for 2 years.

* The cypress wood filter is a consumable item like the circular filter, so please replace it after the replacement period (2 years) has passed.
* If you desire the cypress wood scent, please purchase our diffuser capsule and install it.


The shape of the cypress wood filter is changing.

Our cypress wood filters are crafted from solid wood, which may exhibit scratches, dents, and knots.

Wood naturally expands in the summer as it absorbs moisture and contracts in the winter as it releases moisture. Over time, this process may result in size variations of up to 5mm or the occurrence of cracks in the wood.


ETC

The odor is coming from the air vent.

In the following cases, the device may not operate normally:

1.If there are foreign substances in the air outlet or filter compartment:
Please the air outlet and filter compartment for any foreign substances and remove them.

2. If the filter is heavily covered with dust:
An accumulation of dust on the filter can cause odors. Please use a vacuum cleaner to remove dust from the filter.

If the air purifier was previously used in the kitchen or a smoking area:
Filters are designed to absorb odors, so they might temporarily retain odors from previous usage. However, these odors will gradually diminish with time.
*Residual odors from previous locations may linger.


Power/Operation

The power is not turning on.

In the following cases, the device may not operate normally:
1. Check the power outlet you are using:
Try plugging in another electronic device to verify if electricity is flowing into the outlet. If it operates normally, disconnect the air purifier's power cord for a minute before reconnecting it to reset the device.

2. Ensure the air purifier's power is on:
Press the power button to see if the air purifier turns on.

3. If you've moved the product:
Check the power cord to ensure it's properly connected. (It might have slightly come loose, so try reconnecting it securely.)
* Note: The power cord is designed to detach for safety reasons.


The wind speed is weak.

In the following cases, the device may not operate normally:

1. If the filter packaging is not removed:
Please remove the protective film from the cypress wood filter and the plastic wrapping from the circular filter after purchasing the product.

2. If the filter is not correctly installed:
Ensure that the filter is properly installed before use.

3. If there is a lot of dust accumulated on the filter:
Dust buildup on the filter can result in increased noise levels. Please use a vacuum cleaner to remove the accumulated dust from the filter.

4. If the fan speed setting is in Auto mode or Sleep mode:
Change the fan speed setting to Manual mode or Cyclone mode before use.


Sleep mode isn't working.

In the following cases, the device may not operate normally:
*Our air purifier switches to Sleep Mode based on sensor only during Auto Mode.

1. When the surrounding area is bright:
During Auto Mode operation, please darken the area around the light sensor.
* After setting to Auto mode, if the area around the light sensor is dark, it will switch to Sleep & Eco mode after about 10 seconds.


Noise

The noise during operation is loud.

In the following cases, the device may not operate normally:

1. If the filter packaging is not removed:
Please remove the protective film from the cypress wood filter and the plastic wrapping from the circular filter after purchasing the product.

2. If there is a lot of dust accumulated on the filter:
Dust buildup on the filter can result in increased noise levels. Please use a vacuum cleaner to remove the accumulated dust from the filter.

3. If the fan speed setting is in Auto Mode or Cyclone Mode:
Adjust the fan speed setting to levels 1 to 3 before use.
*In Auto Mode, the fan speed adjusts automatically according to the level of air pollution, leading to variations in operational noise.


There is a noise that sounds like something is getting caught during operation.

In the following cases, the device may not operate normally:

1. Check the connection status of the product's legs.
Ensure that there are no incorrectly connected areas between the main body and the legs.

2. If the appliance isn't level:
Please ensure it's placed on a flat surface.
(Uneven floors may cause the appliance to tilt, leading to noise as the fan contacts the internal wall while attempting to maintain its rotation axis.)

3. If there are foreign substances in the air outlet or filter compartment:
Please the air outlet and filter compartment for any foreign substances and remove them.


Circular filter & Cypress wood filter

How do I install/remove the diffuser capsule?

1. Turn off the power and detach the cypress wood filter using the provided detachment hook.
2. Remove the safety mesh.
3. Remove the cover from the diffuser capsule.(Do not remove the transparent film)
4. Place the diffuser capsule into the ventilation fan and secure the cover.
5. Assemble the cypress wood filter to fit the exterior.


How often should the filter be replaced?

The replacement cycle for the circular HEPA filter is one year, and for the cypress wood filter, it is two years.


I don't smell the scent of cypress wood.

Even if there is no scent from the cypress wood filter, its efficacy will last for 2 years.

* The cypress wood filter is a consumable item like the circular filter, so please replace it after the replacement period (2 years) has passed.
* If you desire the cypress wood scent, please purchase our diffuser capsule and install it.


The shape of the cypress wood filter is changing.

Our cypress wood filters are crafted from solid wood, which may exhibit scratches, dents, and knots.

Wood naturally expands in the summer as it absorbs moisture and contracts in the winter as it releases moisture. Over time, this process may result in size variations of up to 1-2 mm or the occurrence of cracks in the wood.


ETC

The odor is coming from the air vent.

In the following cases, the device may not operate normally:

1.If there are foreign substances in the air outlet or filter compartment:
Please the air outlet and filter compartment for any foreign substances and remove them.

2. If the filter is heavily covered with dust:
An accumulation of dust on the filter can cause odors. Please use a vacuum cleaner to remove dust from the filter.

3. If the air purifier was previously used in the kitchen or a smoking area:
Filters are designed to absorb odors, so they might temporarily retain odors from previous usage. However, these odors will gradually diminish with time.
*Residual odors from previous locations may linger.


Power/Operation

The power is not turning on.

In the following cases, the device may not operate normally:

1. Check the vehicle's USB socket.
Ensure that other USB devices connected to the vehicle's USB socket are functioning properly.

2. Check the USB cable.
Verify the connection between the product and the USB cable.
* Please use the USB cable provided with the product.

3. If the product is turned off.
Press and hold the power button for 3 seconds to turn on the power.
* You can press and hold the power button for 3 seconds to turn the power on/off.


The wind speed is weak.

In the following cases, the device may not operate normally:

1. If the filter packaging is not removed:
Please remove the protective film from the cypress wood filter after purchasing the product.

2. If the filter is not correctly installed:
Ensure that the filter is properly installed before use.

3. If there is a lot of dust accumulated on the filter:
Dust buildup on the filter can result in increased noise levels. Please use a vacuum cleaner to remove the accumulated dust from the filter.

4. If the fan speed is set to level 1:
Please adjust the fan speed to levels 2-3 before use.


Circular filter & Cypress wood filter

How do I install/remove the diffuser capsule?

1. Rotate the bottom part of the main body to detach the filter.
2. Remove the cover from the diffuser capsule.(Do not remove the transparent film)
3. Place the diffuser capsule into the holder.
4. Attach the holder to the top part of the filter.
5. Insert the filter into the bottom part of the main body and rotate to secure it.


How often should the filter be replaced?

The replacement cycle for the circular HEPA filter is one year.


I don't smell the scent of cypress wood.

Even if there is no scent from the cypress wood filter, its efficacy will last.-> 2년 지웠어요

* If you desire the cypress wood scent, please purchase our diffuser capsule and install it.


The shape of the cypress wood filter is changing.

Our cypress wood filters are crafted from solid wood, which may exhibit scratches, dents, and knots.

Wood naturally expands in the summer as it absorbs moisture and contracts in the winter as it releases moisture. Over time, this process may result in size variations of up to 1-2 mm or the occurrence of cracks in the wood.


ETC

The odor is coming from the air vent.

In the following cases, the device may not operate normally:

1.If there are foreign substances in the air outlet or filter compartment:
Please the air outlet and filter compartment for any foreign substances and remove them.

2. If the filter is heavily covered with dust:
An accumulation of dust on the filter can cause odors. Please use a vacuum cleaner to remove dust from the filter.

3. If the air purifier was previously used in the kitchen or a smoking area:
Filters are designed to absorb odors, so they might temporarily retain odors from previous usage. However, these odors will gradually diminish with time.
*Residual odors from previous locations may linger.